Ford Mustang Owners Manual: Safety Belts
PRINCIPLES OF OPERATION
: Always drive and ride with your seat back upright and the lap belt snug and low across the hips
: To reduce the risk of injury, make sure children sit where they can be properly restrained.
: Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a crash.
: All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an airbag supplemental restraint system is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.
: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.
: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a safety belt.
: Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder. 3) Never use a single belt for more than one person.
: When possible, all children 12 years old and under should be properly restrained in a rear seating position. Failure to follow this could seriously increase the risk of injury or death.
: Safety belts and seats can become hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.
: Front and rear seat occupants, including pregnant women, should wear safety belts for optimum protection in an accident.
: The center of the rear seat is not designed as a seating position and is not equipped with safety belts. The LATCH anchors were not designed to be used with a child seat in the center position and there is no tether anchor available at the center. Attempted use of the center as a seating position will increase the risk of injury or death in the event of a crash.
All seating positions in this vehicle have lap and shoulder safety belts.
All occupants of the vehicle should always properly wear their safety belts, even when an airbag supplemental restraint system is provided.
The safety belt system consists of:
• lap and shoulder safety belts.
• shoulder safety belt with automatic locking mode, (except driver safety belt).
• retractor pretensioner at the front outboard seating positions.
• belt tension sensor at the front outboard passenger seating position.
• safety belt warning light and chime. See Safety Belt Warning Light and Indicator Chime later in this chapter.
• crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag Indicator in the Supplemental Restraint System chapter.
The safety belt pretensioners are designed to activate in frontal, near-frontal and side crashes. The safety belt pretensioners at the front seating positions are designed to tighten the safety belts firmly against the occupant’s body when activated. This helps increase the effectiveness of the safety belts. In frontal crashes, the safety belt pretensioners can be activated alone or, if the crash is of sufficient severity, together with the front airbags.
- Fastening the safety belts
- Safety belt warning light and indicator chime
- Safety belt-minder
- Child restraint and safety belt maintenance
Installing child seatsChild Seats Use a child safety seat (sometimes called an infant carrier, convertible seat, or toddler seat) for infants, toddlers or children weighing 40 pounds (18 kilograms) or less (generall ...
Fastening the safety beltsThe front outboard and rear safety restraints in your vehicle are combination lap and shoulder belts. The presenter arm (available on the coupe only) is intended to improve access to the safety b ...
Rear Drive Axle/Differential - Ford 8.8-Inch IRS
General Specifications Torque Specifications a: Use Stud and Bearing Mount EOAZ-19554-BA or equivalent meeting Ford specification WSKM2G349- A1. b: With pinion flange yoke seal. ...
Glass, Frames and Mechanisms (Diagnosis and Testing)
Glass, Frames and Mechanisms (Description and Operation) Component Location Windshield Glass The windshield exterior mouldings are installed with the windshield glass. The windshield exterior mouldings cannot be replaced without removal of the w ...
Rear Drive Axle and Differential The axle housing assembly consists of a cast center section with two steel tube assemblies and a stamped differential housing cover (4033). The differential housing cover uses silicone sealant as a gasket. ...